LEARNING THE BASICS OF PLUMBING FOR BATHTUB INSTALLATION

Learning the Basics of Plumbing for Bathtub Installation

Learning the Basics of Plumbing for Bathtub Installation

Blog Article

Quote & Schedule

What're your thoughts on Tools You Need to Install a New Bathtub ?


A Step-by-Step Guide to Installing a Bathtub
Mounting a bathtub isn't exactly brain surgery, yet it does call for strong plumbing, woodworking, as well as often, tiling abilities. Changing an old tub with a brand-new one is likewise a reasonably challenging project. If the old tub is readily easily accessible, the project can move rapidly; if you need to open a wall to remove the old bathtub and also position the brand-new bath tub, the task is much harder. In either instance, the project is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub as well as set in the new one. Make sure you have certified yourself for the task and also are comfortable attempting it. As opposed to employing a service provider to take control of a halfway-completed project, it is far better to take into consideration utilizing one before you start. Opportunities are you might require a professional plumber to make tube connections.
This write-up will help you install a brand-new bath tub in your restroom if you have actually currently bought a new tub and also do not need to alter the plan of your previous water system pipes.
Your devices and product checklist must consist of the following:
  • New Tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  • Removing Old Touches


    If you need to replace old faucets with new ones as a part of your installment, then the first thing you ought to do is separate the water. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The process of getting rid of the existing faucets can be quite bothersome due to the limited access that is often the instance.
    Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the taps. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. Once the supply pipelines have actually been gotten rid of, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single taps from turning throughout this procedure. Once the taps have actually been removed, the holes in the bath/basin will need to be cleaned up of any type of old securing compound.
    Before moving on to fit the new faucets, compare the pipe connections on the old taps to the new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new taps to fit.

    Fitting New Touches


    If the tails of the new faucets are plastic, then you will certainly need a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the tap and also the various other end supplies a connection to the current supply pipelines.
    If you require to fit a monobloc, after that you will certainly require reducing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
    Next, position the tap in the placing hole in the bath/basin ensuring that the washers are in location in between the faucet as well as the sink. Protect the tap in position with the manufacturer given backnut. As soon as the tap is securely in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal faucet ports. The previous kind needs to be attached to the faucet finishes first, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.

    Mounting the Tub


    Using both wooden boards under its feet, position the bathtub in the needed placement. The wooden boards are useful in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto four small factors.
    The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by examining the spirit level as well as changing the feet on the bathtub up until the level reads degree.
    To install taps, fit the bottom of the furthest adaptable tap connector to the ideal supply pipe by making a compression sign up with; then do the very same for the other tap.
    Turn on the supply of water and also inspect all joints and also new pipework for leakages as well as tighten them if required. Load the tub and additionally check the overflow electrical outlet as well as the normal outlet for leakages.
    Finally, take care of the bathroom paneling as defined in the maker's instruction manual. Tiling as well as sealing around the tub needs to wait until the tub has actually been utilized a minimum of once as this will settle it into its final placement.

    Preparing for the Installment


    To start with, the sustaining structure supplied with the bath should be fitted (if needed) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the faucet features a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to avoid stress on the bath tub.
    Fit the adaptable faucet connectors to the bottom of the two faucets using 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet with the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
    Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its final placement.

    Tiling Around the Tub


    In the area where the bathroom satisfies the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to crack a stiff seal, causing the water to permeate the wall in between the bath as well as the tiling, causing difficulties with wetness and possible leakages to the ceiling below.
    You can pick from a selection of coloured sealants to assimilate your fixtures as well as installations. They are marketed in tubes as well as cartridges, as well as can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to load, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to permit the motion experienced when the tub is in usage. The sealant can split rather early if you do not think about this motion prior to securing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally conveniently readily available on the marketplace. It is recommended to fit the floor tiles using water-resistant or water resistant glue and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub

    As a person who reads about Installing A Bathtub, I assumed sharing that piece of content was really useful. Remember to take a moment to promote this article if you enjoyed reading it. We cherish reading our article about How to Install a Bathtub Yourself.


    Don't settle; choose expert plumbers.

    Report this page